-
1 fault safety
Англо-русский словарь промышленной и научной лексики > fault safety
-
2 отказобезопасность
1) Information technology: fail-safe feature3) Astronautics: fail-safe4) Sakhalin energy glossary: intrinsic safetyУниверсальный русско-английский словарь > отказобезопасность
-
3 отказобезопасность
( свойство системы не приводить к аварии при возникновении отказа) fault safetyРусско-английский словарь по нефти и газу > отказобезопасность
-
4 аварийное отключение
- safety shut-down
- fault outage
- emergency trip
- emergency switching-off
- emergency switching
- emergency outage
аварийное отключение
Размыкание коммутационного устройства, предназначенное для отключения питания электроустановки электрической энергией, с целью предотвращения или уменьшения опасности.
[ ГОСТ Р МЭК 60050-826-2009]
аварийное отключение
Отключение, при котором снимается напряжение со всех токоведущих элементов поврежденной энергоустановки.
[ОАО РАО "ЕЭС России" СТО 17330282.27.010.001-2008]EN
emergency switching-off
Opening operation of a switching device intended to remove electric power from an electrical installation to avert or alleviate a hazardous situation.
[IEV number 826-17-03]FR
coupure d'urgence, f
Ouverture d’un dispositif de coupure destinée à couper l’alimentation électrique d’une installation électrique pour supprimer ou réduire un danger.
[IEV number 826-17-03]Тематики
EN
DE
- Not-Ausschaltung, f
FR
- coupure d'urgence, f
3.3.18 аварийное отключение (safety shut-down): Процесс, который запускается сразу после срабатывания аварийного ограничителя или датчика или обнаружения отказа в автоматической системе управления горелками и который отключает горелку, отключая сразу электропитание газового отсечного клапана (газовых отсечных клапанов) и запального устройства.
Источник: ГОСТ Р 54788-2011: Кондиционеры абсорбционные и адсорбционные и/или тепловые насосы газовые с номинальной тепловой мощностью до 70 кВт. Часть 1. Безопасность оригинал документа
Русско-английский словарь нормативно-технической терминологии > аварийное отключение
-
5 НКУ с защитой от воздействия электрической дуги
- internal arc-proof switchgear and controlgear assemblу
- arc-resistant switchgear
- arc-proof switchgear
- arc-proof switchboard
- arc-proof low voltage switchgear and controlgear assembly
НКУ с защитой от воздействия электрической дуги
комплектное устройство с защитой от электрической дуги
низковольтное комплектное устройство с защитой от электрической дуги
НКУ распределения и управления с защитой от электрической дуги
-
[Интент]EN
arc-resistant switchgear
A type of switchgear design which is designed to withstand the effects of an internal arcing fault, without causing harm to personnel who are located in defined areas. It is not intended to withstand these internal arcing fault without possibly causing physical damage to the structure and/or components, but often the physical damage is less with an arc-resistant design.
There are three classes of protection:
Type A - eliminates the emission of gases and particles from the front of the switchgear during an internal arcing fault,
Type B - eliminates the emission of gases and particles from the front and sides of the switchgear during an internal arcing fault,
Type C - eliminates the emission of gases and particles from the front and sides of the switchgear, from between compartments within the same cell, and between adjacent cells during an internal arcing fault.
Arc-resistant switchgear has traditionally been metal-clad, but the basic concept could also be applied to other types of switchgear as well.
arc-proof switchgear
An incorrect term. Please refer to arc-resistant switchgear
[Schneider Electric]
[ http://electrical-engineering-portal.com/glossary-of-medium-voltage-switchgear-terms]Параллельные тексты EN-RU
If the electric arc occurs inside LV switchgear it generates internal overpressures and results in local overheatings which may cause high mechanical and thermal stresses in the equipment.
Besides, the involved materials can generate hot decomposition products, gases or fumes, which, due to the overpressure, are almost always ejected to the outside of the enclosure thus jeopardizing the operator safety.
The European Directive 2006/95/EC states the fundamental safety requirements for low voltage electric materials (from 50 V to 1000 V in alternating current, from 75 V to 1500 V in continuos current) to be put on the market within the European Community.
Among the essential safety requirements defined by this Directive particular importance is given to the need of taking technical measures to prevent “temperature rises, electric arcs or radiations which may result in hazards” from occurring.
This aspect has always been highly considered for apparatus, but it has been wrongly neglected for electrical switchgear and only in the last 10-15 years it has been catching on both at Italian as well as at international level.
Safety for the operator and for the installation in case of arcing inside LV switchgear can be obtained through three different design philosophies:
1. assemblies mechanically capable of withstanding the electric arc (passive protection)
2. assemblies equipped with devices limiting the effects of internal arcing (active protection)
3. assemblies equipped with current limiting circuitbreakers.
These three solutions (also combined together) have found a remakable development in the industrial field and have been successfully applied by the main manufacturers of LV switchgear and controlgear assemblies.
As it can be seen hereafter by examining the first two solutions, an “active” protection against arc faults is intrinsecally more complex than a “passive” one.
This because of the presence of additional electromechanical/ electronic devices5 which limit the arcing effects and which, by their nature, may be subject to faults or not-tripping.
[ABB]Дуга, возникшая внутри НКУ, создает внутреннее избыточное давление и вызывает локальный перегрев, что может привести к воздействию на оборудование значительного механического напряжения и перепада температур.
Кроме того, под воздействием дуги различные материалы разлагаются на продукты, имеющие высокую температуру, в том числе газы и дым, которые почти всегда вырываются из оболочки НКУ под высоким давлением, подвергая опасности оперативный персонал.
Европейская директива 2006/95/EC определяет основные требования безопасности для низковольтного (от 50 до 1000 В переменного тока и от 75 до 1500 В постоянного тока) оборудования поставляемого на рынок Европейского Сообщества.
Одно из основных требований безопасности, определяемое данной директивой как наиболее важное, заключается в необходимости предпринять технические меры для предотвращения "подъема температуры, возникновения электрической дуги или излучения", которые могут причинить ущерб.
Данная проблема всегда учитывалась при создании различных аппаратов, но незаслуженно игнорировалась при разработке электрических комплектных устройств, и только в последние 10-15 лет ей стали уделять должное внимание как в Италии, так и во всем мире.
При возникновении электрической дуги внутри НКУ безопасность оператора и электроустановки обеспечивается тремя способами:
1. Конструкция НКУ должна выдерживать механические воздействия, возникающие при горении электрической дуги (пассивная защита).
2. НКУ должно быть оснащено устройствами, ограничивающими воздействие электрической дуги (активная защита)
3. НКУ должны быть оснащены токоограничивающими автоматическими выключателями.
Указанные три способа (применяемые совместно) получили дальнейшее развитие в промышленности и успешно применяются основными изготовителями НКУ распределения и управления.
Как будет показано далее при рассмотрении первых двух способов, активная защита от дуговых» неисправностей является более сложной, чем пассивная защита.
Это объясняется необходимостью использования дополнительных электромеханических или электронных устройств, задачей которых является ограничение воздействий дуги и которые сами могут оказаться неисправными и не сработать.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
Синонимы
- комплектное устройство с защитой от электрической дуги
- низковольтное комплектное устройство с защитой от электрической дуги
- НКУ распределения и управления с защитой от электрической дуги
EN
Русско-английский словарь нормативно-технической терминологии > НКУ с защитой от воздействия электрической дуги
-
6 отказоустойчивость
1) Computers: fail-safe feature2) Engineering: fault withstandability, fault-tolerance3) Construction: fail safe4) Automobile industry: fail-safety5) Information technology: fall-over protection, resiliency, resilience, failover6) Oil: fail-safe behavior, failure tolerance7) Special term: failsoft (возможность работы системы при отказе отдельных ее элементов), fault-tolerance (возможность работы системы при отказе отдельных ее элементов)8) Microelectronics: fault tolerance9) Chemical weapons: fail safety (сохранение работоспособности системы при отказе отдельных элементов)10) Makarov: failsoft (возможность работы системы при отказе отдельных её элементов), fault-tolerance (возможность работы системы при отказе отдельных её элементов)11) Automatic control: Failure robustnessУниверсальный русско-английский словарь > отказоустойчивость
-
7 сохранение работоспособности при отказе отдельных элементов
1) Engineering: fail safety, fail-safety (системы), fault-tolerance (системы)2) Telecommunications: failsafety3) Information technology: (системы) fault tolerance4) Oil: failed-safe mode (системы)5) Quality control: (системы) fail-safetyУниверсальный русско-английский словарь > сохранение работоспособности при отказе отдельных элементов
-
8 аварийный сигнал
- trouble tone
- signal alarm
- safety signal
- fault signal
- fate signal
- emergency signal
- beacon
- BCN
- alert message
- alarm signal
- alarm
аварийный сигнал
alarm
Сигнал оповещения, генерируемый в случае, если произошел отказ или контролируемый параметр вышел за допустимые пределы.
[Л.М. Невдяев. Телекоммуникационные технологии. Англо-русский толковый словарь-справочник. Под редакцией Ю.М. Горностаева. Москва, 2002]
аварийный сигнал
beacon
BCN
Сигнал, посылаемый от неисправного узла сети.
[Л.М. Невдяев. Телекоммуникационные технологии. Англо-русский толковый словарь-справочник. Под редакцией Ю.М. Горностаева. Москва, 2002]
аварийный сигнал
fate signal
Сообщение, сигнализирующее об отказе или пропадании входной информации.
[Л.М. Невдяев. Телекоммуникационные технологии. Англо-русский толковый словарь-справочник. Под редакцией Ю.М. Горностаева. Москва, 2002]
аварийный сигнал
safety signal
Сигнал, поступающий отдатчиков охранной сигнализации.
[Л.М. Невдяев. Телекоммуникационные технологии. Англо-русский толковый словарь-справочник. Под редакцией Ю.М. Горностаева. Москва, 2002]EN
alarm
activation of an event that shows a critical state
[IEC 61158-5-10, ed. 2.0 (2010-08)]
alarm
type of Event associated with a state condition that typically requires acknowledgement
[ IEC 62541-1, ed. 1.0 (2010-02)]
alarm
an audible, visual, or other signal activated when the instrument reading exceeds a preset value or falls outside of a preset range
[IEC 62533, ed. 1.0 (2010-06)]
alarm
warning of the presence of a hazard to life, property or the environment
[IEC 62642-1, ed. 1.0 (2010-06)]
alarm
audio and visual signal announcing a condition requiring attention. The audio continues until acknowledged. The acoustic noise pressure of the alarm is at least 75 dBA but not greater than 85 dBA at a distance of 1 m (IEC 60945). The visual indication continues until the alarm condition is removed
[IEC 62065, ed. 1.0 (2002-03)]
alarm
item of diagnostic, prognostic, or guidance information, which is used to alert the operator and to draw his or her attention to a process or system deviation
NOTE Specific information provided by alarms includes the existence of an anomaly for which corrective action might be needed, the cause and potential consequences of the anomaly, the overall plant status, corrective action to the anomaly, and feedback of corrective actions.
Two types of deviation may be recognised:
– unplanned – undesirable process deviations and equipment faults;
– planned – deviations in process conditions or equipment status that are the expected response to but could be indicative of undesirable plant conditions.
[IEC 62241, ed. 1.0 (2004-11)]FR
alarme
signal sonore, visuel ou autre, activé lorsque la lecture de l’instrument excède une valeur préréglée ou sortant d’un domaine déterminé
[IEC 62533, ed. 1.0 (2010-06)]
alarme
avertissement de la présence d'un risque concernant la vie, la propriété ou l'environnement
[IEC 62642-1, ed. 1.0 (2010-06)]
alarme
élément informatif relatif au diagnostic, au pronostique ou à une recommandation, qui est utilisé pour alerter l’opérateur et pour attirer son attention sur une déviation du procédé ou d’un système
NOTE L’information particulière fournie par les alarmes couvre l’existence d’anomalies pour lesquelles une action corrective pourrait être nécessaire, la cause et les conséquences potentielles de l’anomalie, l’état général de la centrale, l’action corrective correspondant à l’anomalie et le retour de l’action corrective.
Deux types de déviation peuvent être distingués:
– non prévue – Déviations du procédé indésirable et défaillance de matériels;
– prévue – Déviations relatives aux conditions du procédé ou aux états des matériels qui sont les réponses prévues, mais qui peuvent être indicatives de conditions indésirables pour la centrale.
[IEC 62241, ed. 1.0 (2004-11)]Параллельные тексты EN-RU
When the accumulated energy dropout setpoint and time delay are satisfied, the alarm is inactive.
[Schneider Electric]Если подсчитанное количество электроэнергии становится меньше заданного максимального значения и заданное время задержки истекло, аварийный сигнал отключается.
[Перевод Интент]
Тематики
- автоматизация, основные понятия
- релейная защита
- электросвязь, основные понятия
Действия
EN
- alarm
- alarm signal
- alert message
- BCN
- beacon
- emergency signal
- fate signal
- fault signal
- safety signal
- signal alarm
- trouble tone
FR
3.2.2 аварийный сигнал (alarm signal): Звуковой, световой, электрический или сигнал другого типа, выдаваемый газоанализатором, когда измеренное значение содержания определяемого компонента достигает порогового значения.
Источник: ГОСТ Р 52350.29.4-2011: Взрывоопасные среды. Часть 29-4. Газоанализаторы. Общие технические требования и методы испытаний газоанализаторов горючих газов с открытым оптическим каналом оригинал документа
Русско-английский словарь нормативно-технической терминологии > аварийный сигнал
-
9 надёжность
1) General subject: credibility, fail-safety, reliability, reliability (инф.), reliance, safety, security, trustability, trustiness2) Computers: safe3) Medicine: responsibility4) Engineering: availability, durability, integrity, margin of safety5) Railway term: reliability (действия или работы)6) Law: reliability of evidence, reliability of testimony, testimonial reliability7) Economy: fail-safety (при отказе отдельных элементов)8) Architecture: solidity9) Textile: serviceability10) Oil: demonstrated reliability, infallibility, safety (в работе)11) Special term: security of service12) Astronautics: unfailing performance13) Advertising: trustworthiness14) Business: dependence, surety15) Household appliances: failsafety16) Automation: fault-tolerance, robustness17) Quality control: accuracy, (общая) dependability, reliability function, safety margin, soundness18) Makarov: fail-safe feature, security service, validity19) Combustion gas turbines: reliability (в работе) -
10 надежность
1) General subject: credibility, fail-safety, reliability, reliability (инф.), reliance, safety, security, trustability, trustiness2) Computers: safe3) Medicine: responsibility4) Engineering: availability, durability, integrity, margin of safety5) Railway term: reliability (действия или работы)6) Law: reliability of evidence, reliability of testimony, testimonial reliability7) Economy: fail-safety (при отказе отдельных элементов)8) Architecture: solidity9) Textile: serviceability10) Oil: demonstrated reliability, infallibility, safety (в работе)11) Special term: security of service12) Astronautics: unfailing performance13) Advertising: trustworthiness14) Business: dependence, surety15) Household appliances: failsafety16) Automation: fault-tolerance, robustness17) Quality control: accuracy, (общая) dependability, reliability function, safety margin, soundness18) Makarov: fail-safe feature, security service, validity19) Combustion gas turbines: reliability (в работе) -
11 отказоустойчивость
fail-safety, fault-tolerance, fault withstandabilityРусско-английский политехнический словарь > отказоустойчивость
-
12 FS
forged steel — кованая сталь, стальные поковки -
13 координация (контакторов и пускателей) с устройствами защиты от короткого замыкания
координация (контакторов и пускателей) с устройствами защиты от короткого замыкания
-7.2.5 Координация с аппаратами защиты от коротких замыканий
7.2.5.1 Работоспособность в условиях короткого замыкания (номинальный условный ток короткого замыкания)
... Допускается координация двух типов — 1 или 2....
Координация типа 1 требует, чтобы в условиях короткого замыкания контактор или пускатель не создавали опасности для людей или оборудования, хотя они могут оказаться непригодными для дальнейшей эксплуатации без ремонта и замены частей.
Координация типа 2 требует, чтобы в условиях короткого замыкания контактор или пускатель не создавали опасности для людей или оборудования и оставались пригодными для дальнейшей эксплуатации. Возможность сваривания контактов допускается, и в этом случае изготовитель должен рекомендовать меры по обслуживанию аппаратов.
[ ГОСТ Р 50030.4.1-2002 (МЭК 60947-4-1-2000)]Параллельные тексты EN-RU
Co-ordination type 1 and type 2
The co-ordination typologies admitted by the Standard with reference to the behavior of the protection device against short-circuit towards the starter components are classified as “type 1” and “type 2”.
Under short-circuit conditions, the coordination of type “1” allows the contactor and the overload relay to be damaged; as a consequence they could not be able to operate without repairing or replacement of parts.
However, the Standard prescribes that these devices do not cause damages to people or installations, for example with parts of the components ejected outside the enclosure.
Under short-circuit conditions, the coordination of type “2” allows the risk of contact welding, provided that the contacts themselves can be easily separated (for example through a screwdriver) without important deformations.
This type of coordination requires that the contactor or the starter do not cause damages to people or installation and that they are able to resume operation after restoring of the standard conditions.
From the definition of the two coordination typologies it is possible to deduce how “type 1” coordination permits the use of devices of lower sizes, thus with an initial cost saving and reduced dimensions, but to the disadvantage of a high safety and however with subsequent costs for maintenance and replacement in case of faults.
“Type 2” coordination meets higher safety requirements and the possible greater initial cost can be amortized considering that, in case of fault, the switching and protection equipment could start operating again without being replaced.
[ABB]Координация типа 1 и 2 с аппаратами защиты от коротких замыканий
Стандарт определяет два типа координации компонентов пускателя с аппаратами защиты от короткого замыкания: тип 1 и тип 2.
Координация типа 1. В условиях короткого замыкания допускается повреждение контактора и теплового реле, в результате чего они могут оказаться непригодными для дальнейшей эксплуатации без ремонта и замены частей. При этом данные устройства не должны создавать опасности для людей и оборудования, например, вследствие вылета частей пускателя из оболочки.
Координация типа 2. В условиях короткого замыкания допускает сваривание контактов при условии, что они могут быть легко разъединены (например, отверткой) без заметной деформации. Контактор и тепловое реле не должны создавать опасности для людей и оборудования и должны оставаться пригодными для дальнейшей эксплуатации после восстановления нормальных условий.
Из определения двух типов координации можно сделать вывод, что координация типа 1 позволяет использовать устройства, рассчитанные на меньшие рабочие токи, обеспечивая таким образом экономию на первоначальных затратах и сокращение размеров устройств, но снижая при этом уровень безопасности и приводя впоследствии к расходам на техническое обслуживание и замену в случае возникновения неисправности.
Координация типа 2 отвечает более высоким требованиям безопасности и имеет большие первоначальные расходы, которые могут быть компенсированы тем, что в случае возникновения неисправности эксплуатация коммутационных и защитных аппаратов может быть продолжена без замены их частей.
[Перевод Интент]Тематики
EN
Русско-английский словарь нормативно-технической терминологии > координация (контакторов и пускателей) с устройствами защиты от короткого замыкания
-
14 аварийный сигнал
аварийный сигнал
alarm
Сигнал оповещения, генерируемый в случае, если произошел отказ или контролируемый параметр вышел за допустимые пределы.
[Л.М. Невдяев. Телекоммуникационные технологии. Англо-русский толковый словарь-справочник. Под редакцией Ю.М. Горностаева. Москва, 2002]
аварийный сигнал
beacon
BCN
Сигнал, посылаемый от неисправного узла сети.
[Л.М. Невдяев. Телекоммуникационные технологии. Англо-русский толковый словарь-справочник. Под редакцией Ю.М. Горностаева. Москва, 2002]
аварийный сигнал
fate signal
Сообщение, сигнализирующее об отказе или пропадании входной информации.
[Л.М. Невдяев. Телекоммуникационные технологии. Англо-русский толковый словарь-справочник. Под редакцией Ю.М. Горностаева. Москва, 2002]
аварийный сигнал
safety signal
Сигнал, поступающий отдатчиков охранной сигнализации.
[Л.М. Невдяев. Телекоммуникационные технологии. Англо-русский толковый словарь-справочник. Под редакцией Ю.М. Горностаева. Москва, 2002]EN
alarm
activation of an event that shows a critical state
[IEC 61158-5-10, ed. 2.0 (2010-08)]
alarm
type of Event associated with a state condition that typically requires acknowledgement
[ IEC 62541-1, ed. 1.0 (2010-02)]
alarm
an audible, visual, or other signal activated when the instrument reading exceeds a preset value or falls outside of a preset range
[IEC 62533, ed. 1.0 (2010-06)]
alarm
warning of the presence of a hazard to life, property or the environment
[IEC 62642-1, ed. 1.0 (2010-06)]
alarm
audio and visual signal announcing a condition requiring attention. The audio continues until acknowledged. The acoustic noise pressure of the alarm is at least 75 dBA but not greater than 85 dBA at a distance of 1 m (IEC 60945). The visual indication continues until the alarm condition is removed
[IEC 62065, ed. 1.0 (2002-03)]
alarm
item of diagnostic, prognostic, or guidance information, which is used to alert the operator and to draw his or her attention to a process or system deviation
NOTE Specific information provided by alarms includes the existence of an anomaly for which corrective action might be needed, the cause and potential consequences of the anomaly, the overall plant status, corrective action to the anomaly, and feedback of corrective actions.
Two types of deviation may be recognised:
– unplanned – undesirable process deviations and equipment faults;
– planned – deviations in process conditions or equipment status that are the expected response to but could be indicative of undesirable plant conditions.
[IEC 62241, ed. 1.0 (2004-11)]FR
alarme
signal sonore, visuel ou autre, activé lorsque la lecture de l’instrument excède une valeur préréglée ou sortant d’un domaine déterminé
[IEC 62533, ed. 1.0 (2010-06)]
alarme
avertissement de la présence d'un risque concernant la vie, la propriété ou l'environnement
[IEC 62642-1, ed. 1.0 (2010-06)]
alarme
élément informatif relatif au diagnostic, au pronostique ou à une recommandation, qui est utilisé pour alerter l’opérateur et pour attirer son attention sur une déviation du procédé ou d’un système
NOTE L’information particulière fournie par les alarmes couvre l’existence d’anomalies pour lesquelles une action corrective pourrait être nécessaire, la cause et les conséquences potentielles de l’anomalie, l’état général de la centrale, l’action corrective correspondant à l’anomalie et le retour de l’action corrective.
Deux types de déviation peuvent être distingués:
– non prévue – Déviations du procédé indésirable et défaillance de matériels;
– prévue – Déviations relatives aux conditions du procédé ou aux états des matériels qui sont les réponses prévues, mais qui peuvent être indicatives de conditions indésirables pour la centrale.
[IEC 62241, ed. 1.0 (2004-11)]Параллельные тексты EN-RU
When the accumulated energy dropout setpoint and time delay are satisfied, the alarm is inactive.
[Schneider Electric]Если подсчитанное количество электроэнергии становится меньше заданного максимального значения и заданное время задержки истекло, аварийный сигнал отключается.
[Перевод Интент]
Тематики
- автоматизация, основные понятия
- релейная защита
- электросвязь, основные понятия
Действия
EN
- alarm
- alarm signal
- alert message
- BCN
- beacon
- emergency signal
- fate signal
- fault signal
- safety signal
- signal alarm
- trouble tone
FR
Русско-французский словарь нормативно-технической терминологии > аварийный сигнал
-
15 живучесть
1) General subject: persistence, sap, subsistence, viability, vitality, durability3) American: starch4) Military: ability to survive, capability of survival, endurance, firing life (огнестрельного оружия)5) Engineering: survivability, tenacity6) Rare: vivacity7) Chemistry: survivorship8) Jargon: gimp9) Information technology: liveness (свойство системы), robustness, survival10) Oil: survivability (как критерий погодной устойчивости морского основания), survivability (как критерий погодной устойчивости основания)11) Astronautics: life12) Advertising: staying power13) Household appliances: survivance14) Automation: liveness (напр. системы управления)15) Makarov: brass, fail-safety, failure survival, fault tolerance, longevity, probability of survival, tolerance to failure, viable -
16 надёжный
1) General subject: all-right, anchored, authoritative, calculable, certain, confidential, copper-bottomed, dependable, durable, enduring, escape-proof (о месте заключения), fiducial, firm, fool-proof, good (a good man for - человек, подходящий для), holocryptic (о шифре), infallible, never-failing, pickproof, pight, racked, reliable, responsible, right-on, safe, secure, solid, sound, standfast, steady, steady-going, sterling, straight, sure, tenable, tried, true as the needle to the pole, trustworthy, unprecarious, well-knit, yeomanly2) Computers: trusted3) Geology: foolproof4) Biology: fail-safe (напр. об аппаратуре)5) Naval: fault-free6) Medicine: fail-safe7) Colloquial: surefire8) Obsolete: trusty, warrantable9) Military: robust10) Religion: trust-worthy11) Economy: fail-safe (при отказе отдельных элементов), risk free, risk-free, riskfree12) Automobile industry: reliable (напр. в эксплуатации, в работе, в действии), stand-by, trouble-proof13) Architecture: fail-safe (об оборудовании), failure-safe (об оборудовании)14) Mining: competent15) Diplomatic term: safe (партнёр и т.д.)16) Forestry: regular17) Jargon: lace-curtain, right, white, workshoe18) Information technology: crashproof20) Special term: trouble-free21) Mechanic engineering: proper (об изоляции, о смазке)22) Business: credible, creditable, premium, valid, well-established23) Drilling: time-tested24) Network technologies: trust25) Polymers: safety26) Automation: failsafe, failsoft, positive, positive-acting27) Quality control: accurate28) Aviation medicine: trusting29) Makarov: dependable (напр. о показаниях приборов), heavy, risk-free (о ценных бумагах), riskfree (о ценных бумагах), sound (в финансовом отношении), sterile, tenable (о методе)30) Combustion gas turbines: reliable (в эксплуатации)31) Phraseological unit: bulletproof (Reliable, infallible, sturdy.) -
17 надежный
1) General subject: all-right, anchored, authoritative, calculable, certain, confidential, copper-bottomed, dependable, durable, enduring, escape-proof (о месте заключения), fiducial, firm, fool-proof, good (a good man for - человек, подходящий для), holocryptic (о шифре), infallible, never-failing, pickproof, pight, racked, reliable, responsible, right-on, safe, secure, solid, sound, standfast, steady, steady-going, sterling, straight, sure, tenable, tried, true as the needle to the pole, trustworthy, unprecarious, well-knit, yeomanly2) Computers: trusted3) Geology: foolproof4) Biology: fail-safe (напр. об аппаратуре)5) Naval: fault-free6) Medicine: fail-safe7) Colloquial: surefire8) Obsolete: trusty, warrantable9) Military: robust10) Religion: trust-worthy11) Economy: fail-safe (при отказе отдельных элементов), risk free, risk-free, riskfree12) Automobile industry: reliable (напр. в эксплуатации, в работе, в действии), stand-by, trouble-proof13) Architecture: fail-safe (об оборудовании), failure-safe (об оборудовании)14) Mining: competent15) Diplomatic term: safe (партнёр и т.д.)16) Forestry: regular17) Jargon: lace-curtain, right, white, workshoe18) Information technology: crashproof20) Special term: trouble-free21) Mechanic engineering: proper (об изоляции, о смазке)22) Business: credible, creditable, premium, valid, well-established23) Drilling: time-tested24) Network technologies: trust25) Polymers: safety26) Automation: failsafe, failsoft, positive, positive-acting27) Quality control: accurate28) Aviation medicine: trusting29) Makarov: dependable (напр. о показаниях приборов), heavy, risk-free (о ценных бумагах), riskfree (о ценных бумагах), sound (в финансовом отношении), sterile, tenable (о методе)30) Combustion gas turbines: reliable (в эксплуатации)31) Phraseological unit: bulletproof (Reliable, infallible, sturdy.) -
18 отказоопасность
1) Information technology: fault intolerance2) Sakhalin energy glossary: non-intrinsic safety (отказ может привести к опасной ситуации) -
19 сохранение работоспособности (системы) при отказе отдельных элементов
1) Information technology: fault tolerance2) Quality control: fail-safetyУниверсальный русско-английский словарь > сохранение работоспособности (системы) при отказе отдельных элементов
-
20 отказ
(напр. от права на патент, от одобрения проекта) abandonment, failure, ( схемы) bug, breakdown, fault, refusal* * *отка́з м.1. refusal2. т. над. failureбезавари́йный отка́з — fail-safe operation, fail-safetyотка́з взры́ва — misfireвнеза́пный отка́з — random [unpredictable, catastrophic] failureвре́менный отка́з — temporary failureвтори́чный отка́з — dependent [secondary] failureотка́з, вы́званный изна́шиванием — wear-out failureзави́симый отка́з — dependent [secondary] failureконструкцио́нный отка́з — design error failureкрити́ческий отка́з — critical failureнезави́симый отка́з — independent [primary] failureотка́з от разгово́ра тлф. — cancellation [withdrawal] of a callочеви́дный отка́з — apparent failureперви́чный отка́з — independent [primary] failureперемежа́ющийся отка́з — intermittent failureотка́з пери́ода прирабо́тки — infant failureпо́лный отка́з — complete failureотка́з по (несовпаде́нию) чё́тности вчт. — parity failureпостепе́нный отка́з — degradation of performance, creeping(-type) failureпреждевре́менный отка́з — premature failureскры́тый отка́з — latent failureслуча́йный отка́з — random [unpredictable, catastrophic] failureуста́лостный отка́з — endurance [fatigue] failureчасти́чный отка́з — partial failure* * *
- 1
- 2
См. также в других словарях:
Safety engineering — is an applied science strongly related to systems engineering and the subset System Safety Engineering. Safety engineering assures that a life critical system behaves as needed even when pieces fail.In the real world the term safety engineering… … Wikipedia
Fault tree analysis — (FTA) is a failure analysis in which an undesired state of a system is analyzed using boolean logic to combine a series of lower level events. This analysis method is mainly used in the field of safety engineering to quantitatively determine the… … Wikipedia
fault — n [Anglo French faute lack, failing, ultimately from Latin fallere to deceive, disappoint] 1: a usu. intentional act forbidden by law; also: a usu. intentional omission to do something (as to exercise due care) required by law see also negligence … Law dictionary
Fault-tolerant design — In engineering, Fault tolerant design, also known as fail safe design, is a design that enables a system to continue operation, possibly at a reduced level (also known as graceful degradation), rather than failing completely, when some part of… … Wikipedia
Fault (legal) — The meaning of fault Different forms of liability employ different notions of fault, in some there is no need to prove fault. Fault basically refers to legal blameworthiness and responsibility in each area of law. It refers to both the Actus Reus … Wikipedia
Safety life cycle — The safety life cycle is the series of phases from initiation and specifications of safety requirements, covering design and development of safety features in a safety critical system, and ending in decommissioning of that system. The basic… … Wikipedia
Arc-fault circuit interrupter — An arc fault circuit interrupter (AFCI) is a circuit breaker designed to prevent fires by detecting non working electrical arcs and disconnect power before the arc starts a fire. The AFCI should distinguish between a working arc that may occur in … Wikipedia
Hayward Fault Zone — The Hayward Fault Zone is a geologic fault zone capable of generating significantly destructive earthquakes. About 60 kilometers long, it lies mainly along the western base of the hills on the east side of San Francisco Bay. It runs through… … Wikipedia
Laser safety — A typical laser warning symbol. Laser safety is safe design, use and implementation of lasers to minimize the risk of laser accidents, especially those involving eye injuries. Since even relatively small amounts of laser light can lead to… … Wikipedia
Air safety — is a term encompassing the theory, investigation and categorization of flight failures, and the prevention of such failures through regulation, education and training. It can also be applied in the context of campaigns that inform the public as… … Wikipedia
Food safety in the People's Republic of China — Food safety is a growing concern in Chinese agriculture. China s principal crops are rice, corn, wheat, soybeans, and cotton in addition to apples and other fruits and vegetables. [USDA. [http://www.ers.usda.gov/briefing/china/keystatistics.htm… … Wikipedia